Tool · Custom vehicle
Custom vehicle: model acceleration from your own numbers
Type in a car’s specifications and the model runs it from a standstill. You get the 0–60 mph and 0–100 km/h times, the distance marks out to 1000 m, a range for each headline time, and the assumptions the model had to make for everything you left out.
Add a second car and the tool compares the two the way the rest of this site does: it varies the assumptions for both cars together, looks at the spread of the time difference, and says “too close to call” when that spread does not clearly favor one of them. It then swaps one group of inputs at a time between the cars to show which input the difference comes from.
Your inputs
The page starts with an illustrative car: a made-up vehicle with round numbers, not a real one. Overwrite any value, or load another illustrative car as a starting point. Values are shown in the units chosen in the Units menu and handled internally in SI units.
These inputs need fixing
Results
Modeled from your inputs
These results are for the last inputs the model accepted. They will update once every input is valid.
0–60 mph
8.44s
Illustrative gasoline hatchback
8.25–9.14 s across the assumption ranges
0–100 km/h
8.91s
Illustrative gasoline hatchback
8.72–9.62 s across the assumption ranges
Illustrative gasoline hatchback: the model estimates 0–60 mph in 8.44 s and 0–100 km/h in 8.91 s, both counted from rest. It covers the quarter mile in 16.39 s, crossing the line at 140.5 km/h.
Modeled estimate
Every metric the model produces
| Metric | From rest (s) | After 1-foot rollout (s) | At that point |
|---|---|---|---|
| 0–60 mph | 8.44 | 8.08 | after 134.4 m |
| 0–100 km/h | 8.91 | 8.55 | after 147.3 m |
| 100 m | 7.11 | 6.75 | 89.3 km/h |
| 200 m | 10.70 | 10.34 | 112.4 km/h |
| 400 m | 16.33 | 15.97 | 140.2 km/h |
| Quarter mile | 16.39 | 16.03 | 140.5 km/h |
| 1000 m | 29.54 | 29.18 | 180.2 km/h |
The 0–60 mph and 0–100 km/h rows end at a speed, so the last column gives the distance covered. The other rows end at a distance, so it gives the speed.
The run, plotted
- Illustrati…e hatchback (solid line, round marker)
- Add a second car to draw both runs on the same axes.
Drag, or use the arrow keys, to read both series at a chosen time.
Show the data as a table
| Time (s) | Speed (km/h) | Distance (m) | Accel. (m/s²) | Gear |
|---|---|---|---|---|
| 0.0 | 0.0 | 0.0 | 4.75 | 1 |
| 2.0 | 34.1 | 9.5 | 4.66 | 1 |
| 4.0 | 57.5 | 36.1 | 3.05 | 2 |
| 6.0 | 78.8 | 74.1 | 2.79 | 2 |
| 8.0 | 93.3 | 122.8 | 2.06 | 3 |
| 10.0 | 107.7 | 178.7 | 1.92 | 3 |
| 12.0 | 120.7 | 242.2 | 1.70 | 3 |
| 14.0 | 131.9 | 312.5 | 1.35 | 3 |
| 16.0 | 138.8 | 387.4 | 1.24 | 4 |
| 18.0 | 147.4 | 466.9 | 1.14 | 4 |
| 20.0 | 155.2 | 550.9 | 1.04 | 4 |
| 22.0 | 162.3 | 639.2 | 0.93 | 4 |
| 24.0 | 168.6 | 731.1 | 0.81 | 4 |
| 26.0 | 173.9 | 826.3 | 0.68 | 4 |
| 28.0 | 176.8 | 923.5 | 0.63 | 5 |
Modeled estimate
Which car is quicker
Add a second car to compare two sets of inputs.
Assumption
Assumptions used in this run
These inputs are not part of the car’s stated specifications, so the model chooses them. The run above uses the “value used” column; the range line under each time shows how far the result moves when every assumption is varied across its range.
| Assumption | Value used | Range considered |
|---|---|---|
| Idle speed (rpm) | 800 | 700 – 900 |
| Torque at idle ÷ peak torque | 0.75 | 0.60 – 0.88 |
| Power lost between peak-power speed and the rev limit | 0.08 | 0.02 – 0.20 |
| Engine speed held at launch (rpm) | 4,000 | 2,800 – 5,200 |
| Gear-change time (s) | 0.35 | 0.25 – 0.50 |
| Engine rotational inertia (kg·m²) | 0.20 | 0.10 – 0.35 |
| Drag coefficient (Cd) | 0.30 | 0.26 – 0.36 |
| Frontal area ÷ (width × height) | 0.84 | 0.78 – 0.88 |
| Rolling-resistance coefficient | 0.011 | 0.008 – 0.014 |
| Loaded tire radius ÷ nominal radius | 0.965 | 0.950 – 0.980 |
| Driveline efficiency | 0.91 | 0.88 – 0.94 |
| Share of weight on the front axle | 0.61 | 0.57 – 0.64 |
| Center-of-gravity height (m) | 0.57 | 0.52 – 0.61 |
| Rotational inertia per axle (kg·m²) | 2.2 | 1.5 – 3.5 |
| Grip multiplier (tire and surface variation) | 1.00 | 0.92 – 1.08 |
Left empty for Illustrative gasoline hatchback, so assumed by the model: Share of weight on the front axle, Drag coefficient (Cd), and Frontal area.
Conditions
- Level road, no wind
- Air density 1.2 kg/m³
- No occupants or cargo added to the vehicle mass
- Closed-course, straight-line run from a standstill
- Tire–road grip μ = 1.00
- Times are counted from first movement unless a column says otherwise
- Ranges and the comparison use 120 runs with the assumptions varied
- A car is called quicker only if it is quicker in at least 90% of those runs; that threshold is provisional
- Model version 0.3.0
The range is how far the result moves when the assumptions move. It is not a statistical confidence interval against measured results.
What this tool checks, and what it cannot
The model rejects inputs that cannot all be true at once. The usual cause is a unit mix-up: a power figure in horsepower typed as kilowatts, or torque in pound-feet typed as newton-meters. Power, torque and engine speed are tied together by power = torque × rotational speed, so a peak power that would need more torque than the stated peak torque is refused with a message next to the field.
It cannot tell whether a set of plausible numbers is right. A wrong mass or a gear ratio taken from a different version of the car produces a confident-looking result all the same. Treat the output as a statement about the numbers you typed, and check those against the document you took them from.
Hybrids and continuously variable transmissions are outside the model, so there is no way to enter them here.