Guide · Resistance

Air resistance and speed: why drag grows so fast

Aerodynamic drag force grows with the square of speed, and the power needed to overcome it grows with the cube. The force is ½ × ρ × Cd × A × v², where ρ is the density of the air, Cd the drag coefficient, A the frontal area and v the speed through the air. Double the speed and the force is four times as large; the power is eight times as large.

For acceleration, this means drag matters little at low speed and a great deal at high speed: it barely moves a 0–100 km/h time and moves a 100–200 km/h time a lot. For top speed, it means extra power buys very little. Where top speed is set by power rather than by gearing, it rises only with about the cube root of power, so going 10% faster takes about 33% more power. What counts is the product Cd × A, the drag area. Neither number alone lets you compare two cars.

Updated Model version 0.3.0

DraftThis page has not completed editorial review. It is hidden from search engines until it has.

The drag equation

Drag is the force the air exerts against a body moving through it. For a car at ordinary road speeds, this site’s model uses the form below, with a constant drag coefficient.

drag force = ½ × ρ × Cd × A × v²

Power is force multiplied by speed, so the power spent on drag is the force times v again: ½ × ρ × Cd × A × v³. The table shows what those exponents do.

drag power = ½ × ρ × Cd × A × v³

For the example car in the calculator below, with a drag area of 0.63 m² in air of 1.2 kg/m³, drag is 292 N at 100 km/h and 1,167 N at 200 km/h. Holding those speeds against drag alone takes 8.1 kW and 64.8 kW.

How drag scales with speed
SpeedDrag forceDrag power
× 1× 1× 1
× 1.5× 2.25× 3.375
× 2× 4× 8
× 3× 9× 27

Arithmetic: the square and the cube of the speed factor.

Drag area: why Cd alone is not enough

The drag coefficient Cd describes shape: how cleanly the air flows around the body. The frontal area A describes size: how much air the body has to push aside. Drag depends on their product, Cd × A, called the drag area and written CdA.

A large vehicle with a low Cd can have more drag than a small one with a higher Cd. A body with Cd 0.25 and a frontal area of 2.8 m² has a drag area of 0.70 m². One with Cd 0.32 and 2.0 m² has 0.64 m², about 9% less, despite the worse coefficient.

When a frontal area is not published, this site’s model estimates it as width × height × a factor, and lists that factor among its assumptions.

Rolling resistance, and where drag overtakes it

The other resistance on a level road comes from the tires. This site’s model treats it as a rolling-resistance coefficient (Crr) × mass × g, the same at every speed.

Drag starts at zero and grows with v², so there is a speed at which the two are equal: v = √(2 × Crr × m × g ÷ (ρ × Cd × A)). For the example car in the calculator below (1,500 kg, Crr 0.011, drag area 0.63 m², air at 1.2 kg/m³), that speed is 20.7 m/s, which is 74 km/h (46 mph).

Below that speed the tires cost more than the air. Above it the air takes over quickly: at twice that speed, drag is four times the rolling resistance.

What drag does to acceleration

The force left to accelerate a car is the thrust at the tires minus resistance. At low speed, drag is a small subtraction from a large thrust. At high speed it is a large subtraction from a thrust that has itself fallen, because thrust is limited by power ÷ speed.

That is why a change in drag area hardly shows in a 0–100 km/h time and shows clearly between 100 and 200 km/h. The experiment below puts numbers on both for an illustrative car.

Top speed set by power

A car stops accelerating when resistance × speed equals the power arriving at the driven wheels: ½ × ρ × Cd × A × v³ + Crr × m × g × v = P. That equation has one solution for v, and it is the power-limited top speed.

If drag were the only resistance, v would be the cube root of 2 × P ÷ (ρ × Cd × A). Top speed would then rise with the cube root of power: 1.1³ = 1.331, so 10% more top speed needs 33% more power, and doubling the power adds only 26%, because the cube root of 2 is 1.26. Halving the drag area is worth exactly as much as doubling the power.

For the example car with 100 kW at the wheels, the full equation gives 223 km/h (139 mph). With twice that power it gives 285 km/h, 28% more. That is a little more than the cube-root rule gives, because rolling resistance takes a larger share of the power at the lower speed.

This holds only if the gearing allows it. A car can run out of engine speed in its top gear, or reach a speed limiter, before it runs out of power. The calculator gives the power-limited figure and ignores gearing.

Air density

Drag is proportional to the density of the air. For a gas in ordinary conditions, density is proportional to pressure and inversely proportional to absolute temperature (the ideal-gas relation). At the same pressure, air at 35 °C is about 8% less dense than air at 10 °C, because 283.15 K ÷ 308.15 K = 0.919, and drag falls by the same 8%.

The experiments on this site use 1.2 kg/m³ unless they say otherwise, and the model accepts values from 0.9 to 1.4 kg/m³ in its experiments.

When air density changes, this model changes only the drag term. It does not change the engine’s output with density, so its results are not predictions for a particular altitude or weather.

Drag and power calculator

Enter a drag coefficient, a frontal area, a mass and a speed. The calculator shows the two resistance forces, the power needed to hold that speed, and the top speed a given power at the wheels could sustain. The example values describe a made-up car, not a real one.

Inputs

m²
kg

This site’s model uses 0.011 as its default assumption.

kg/m³
km/h
kW

After driveline losses. Used for the top-speed result only.

Resistance and power at the chosen speed
QuantityValue
Drag area (Cd × A)0.630 m²
Aerodynamic drag force292 N
Rolling resistance force162 N
Total resistance454 N
Power needed to hold this speed12.6 kW
Of which, to overcome drag8.1 kW
Drag as a share of total resistance64%
Speed at which drag equals rolling resistance74.5 km/h
Power-limited top speed (gearing ignored)223.1 km/h

Arithmetic from the definitions above, not a modeled estimate and not a measurement.

Power needed against speed

  • Total (solid line, round marker)
  • Drag (dashed line, square marker)
  • Thin line: rolling resistance. The dotted horizontal line is the power at the wheels you entered.
Power needed to hold a steady speed on a level road, by speedPower needed to hold a steady speed on a level road with no wind. At 100 km/h this car needs 12.6 kW: 8.1 kW to overcome aerodynamic drag and 4.5 kW for rolling resistance. With 100.0 kW at the wheels, the power-limited top speed is 223.1 km/h.
SummaryPower needed to hold a steady speed on a level road with no wind. At 100 km/h this car needs 12.6 kW: 8.1 kW to overcome aerodynamic drag and 4.5 kW for rolling resistance. With 100.0 kW at the wheels, the power-limited top speed is 223.1 km/h.
Show the data as a table
Power needed to hold a steady speed, by speed
Speed (km/h)Drag (kW)Rolling resistance (kW)Total (kW)
200.10.91.0
400.51.82.3
601.82.74.5
804.13.67.7
1008.14.512.6
12014.05.419.4
14022.26.328.5
16033.27.240.4
18047.38.155.4
20064.89.073.8
22086.39.996.2
240112.010.8122.8
260142.411.7154.1

Try it: change the drag area

The cars are illustrative: made-up vehicles with round numbers, not real ones. Change the drag coefficient or the frontal area, and the model runs the car from rest to 200 km/h. It reports 0–100 km/h and, from the same run, the time between passing 100 km/h and passing 200 km/h.

Inputs

m²

Modeled estimate

Illustrative vehicle

Every result in this section is a modeled estimate for a made-up car. None of it is a figure for a real, named vehicle.

Drag area (CdA)

0.63m²

Cd 0.30 × 2.10 m²

0–100 km/h

5.45s

5.22–5.86 s across the assumption ranges

0–200 km/h

17.12s

16.63–18.03 s across the assumption ranges

100–200 km/h

11.67s

same run: time at 200 km/h minus time at 100 km/h

11.27–12.33 s across the assumption ranges

With a drag area of 0.63 m², the illustrative gasoline coupe reaches 100 km/h in 5.45 s and 200 km/h in 17.12 s, so 100–200 km/h takes 11.67 s.

The run, plotted

  • Your inputs (solid line, round marker)
  • Change an input to compare against the starting point.
Speed against time, illustrative gasoline coupeSpeed against time. With your inputs the car passes 100 km/h at 5.45 s and 200 km/h at 17.12 s.
SummarySpeed against time. With your inputs the car passes 100 km/h at 5.45 s and 200 km/h at 17.12 s.
Show the data as a table
Speed over time
Time (s)Speed (km/h)
0.00.0
1.020.2
2.040.3
3.060.3
4.073.0
5.092.1
6.0104.1
7.0116.5
8.0129.4
9.0141.4
10.0149.7
11.0157.0
12.0165.9
13.0174.3
14.0182.3
15.0189.6
16.0196.3
17.0199.2

Modeled estimate

Starting point and your inputs

Starting point and your inputs: drag area and times
CarCdA (m²)0–100 km/h0–200 km/h100–200 km/h
Starting point0.635.45 s17.12 s11.67 s

Something to try

With the gasoline coupe, raise Cd from 0.30 to 0.50. 0–100 km/h moves by about 0.05 s, while 100–200 km/h moves by about 2 s. Then pick the gasoline hatchback and set the same Cd: with less than half the power, it no longer reaches 200 km/h within the 2,000 m run.

Assumption

Assumptions used in this run

These inputs are not part of the car’s stated specifications, so the model chooses them. The run above uses the “value used” column; the range line under each time shows how far the result moves when every assumption is varied across its range.

Assumptions used in this run
AssumptionValue usedRange considered
Idle speed (rpm)800700 – 900
Torque at idle ÷ peak torque0.750.60 – 0.88
Power lost between peak-power speed and the rev limit0.080.02 – 0.20
Engine speed held at launch (rpm)4,0002,800 – 5,200
Gear-change time (s)0.350.25 – 0.50
Engine rotational inertia (kg·m²)0.200.10 – 0.35
Rolling-resistance coefficient0.0110.008 – 0.014
Loaded tire radius ÷ nominal radius0.9650.950 – 0.980
Driveline efficiency0.910.88 – 0.94
Share of weight on the front axle0.520.47 – 0.56
Center-of-gravity height (m)0.530.49 – 0.57
Rotational inertia per axle (kg·m²)2.21.5 – 3.5
Grip multiplier (tire and surface variation)1.000.92 – 1.08

Conditions

  • Level road, no wind
  • Air density 1.2 kg/m³
  • No occupants or cargo added to the vehicle mass
  • Closed-course, straight-line run from a standstill
  • One run from rest, ended at 205 km/h or after 2,000 m, whichever comes first
  • Cd and frontal area are the inputs above, not assumptions
  • Tire–road grip μ = 1.00
  • Model version 0.3.0

The range is how far the result moves when the assumptions move. It is not a statistical confidence interval against measured results.

How the model works and what it assumes: methodology

What this page leaves out

The model uses one constant Cd and one constant Crr. It has no crosswind, no change of drag with ride height or cooling openings, and no aerodynamic lift or downforce changing the load on the tires.

The electric sedan is left out of this experiment because it is limited to 200 km/h, which makes “time to 200 km/h” a statement about its limiter rather than about drag.

Modeled estimate
The model has been checked against closed-form physics cases, but it has not yet been compared with instrumented test results for real cars. Until that comparison is published, treat every number here as an illustration of cause and effect, not as a prediction for any particular vehicle.

How the model works and what it assumes: methodology