Guide · Power and mass

Power-to-weight ratio: what it tells you and what it cannot

Power-to-weight ratio is a vehicle’s power divided by its mass. In SI units it is watts per kilogram (W/kg), which is the same number as kilowatts per metric ton. It is the most useful single number for how hard a car can accelerate once it is moving, because at any speed the acceleration available from the engine is at most power ÷ (mass × speed).

It is a ceiling, not a prediction. With constant power, unlimited grip and no losses, the time from rest to a speed v would be v² ÷ (2 × power-to-weight ratio). Every real car is slower: at low speed the tires limit acceleration whatever the power, the engine makes its peak power at only one engine speed, and gear changes, drag and rotating parts all take a share. Two cars with the same ratio can therefore post different times. The units need care too, because “hp per ton” can mean several different things.

Updated Model version 0.3.0

DraftThis page has not completed editorial review. It is hidden from search engines until it has.

The definition, and the units that trip people up

Power-to-weight ratio = power ÷ mass. Despite the name, the divisor is mass, not weight. The number you get depends on the power unit, the mass unit, and which of the two is on top.

W/kg and kW/t
Watts per kilogram and kilowatts per metric ton (1 t = 1000 kg) are the same number: 100 W/kg is 100 kW/t.
hp and PS
One mechanical horsepower (hp) is 745.699872 W. One metric horsepower (PS) is 735.49875 W, about 1.4% less. The same engine therefore has a slightly larger number in PS than in hp.
Three different tons
A metric ton (tonne) is 1000 kg. A US short ton is 2000 lb, which is 907.18474 kg. A UK long ton is 2240 lb, which is 1016.0469088 kg. “hp per ton” is 12% larger with the long ton than with the short ton.
Upside-down forms
kg/kW, kg/PS and lb/hp put mass on top. A smaller number is then the better one, and halving it is the same as doubling W/kg.
Which power, which mass
Engine power and power at the wheels give different ratios for the same car. So do the mass of the empty car, the mass with a driver, and the fully loaded mass. Two ratios are comparable only if they made the same choices.

Power-to-weight ratio calculator

Enter a power and a mass. The ratio is shown in every common unit at once, with the ideal times it implies. The example values are those of the illustrative hatchback used in the experiment further down.

Inputs

kW
kg

The same power-to-weight ratio in different units
Expressed asValueUnit
Watts per kilogram84.6W/kg
Kilowatts per metric ton84.6kW/t
Mechanical horsepower per metric ton113.5hp/t
Metric horsepower per metric ton115.0PS/t
Mechanical horsepower per US short ton102.9hp/ton (US)
Mechanical horsepower per UK long ton115.3hp/ton (UK)
Kilograms per kilowatt11.82kg/kW
Kilograms per mechanical horsepower8.81kg/hp
Kilograms per metric horsepower8.69kg/PS
Pounds per mechanical horsepower19.43lb/hp
Ideal time from rest for this ratio (a lower bound, not an estimate)
To reachIdeal time
0–60 mph4.25 s
0–100 km/h4.56 s

Ideal time = speed² ÷ (2 × W/kg): constant power, unlimited grip, no losses. No real car reaches it.

Arithmetic from the definitions above, not a modeled estimate and not a measurement.

The ideal time: a lower bound

Suppose power P were constant from the first instant, all of it reached the road, grip were unlimited and nothing resisted the car. Then all of the work done would become kinetic energy: P × t = ½ × m × v². Solving for time gives the formula below.

For 100 km/h (27.78 m/s) that is 385.8 ÷ (W/kg) seconds. For 60 mph (26.82 m/s) it is 359.7 ÷ (W/kg) seconds. At 100 W/kg the bound is 3.86 s to 100 km/h and 3.60 s to 60 mph.

No car reaches this bound, which is what makes it useful. On a level road with no tailwind, a time below it is not possible with the stated power and mass.

ideal time = v² ÷ (2 × P ÷ m)

Ideal time from rest by power-to-weight ratio
Ratio (W/kg)Ratio (hp per metric ton)0–60 mph0–100 km/h
5067.17.19 s7.72 s
75100.64.80 s5.14 s
100134.13.60 s3.86 s
150201.22.40 s2.57 s
200268.21.80 s1.93 s
300402.31.20 s1.29 s

Arithmetic from the formula above, not measurements and not modeled estimates.

Why real cars are slower than the bound

Grip at low speed
From rest, power ÷ speed would allow enormous thrust, but the driven tires can pass at most their grip coefficient times the load they carry. Until speed has risen enough for the power limit to fall below the grip limit, tires and weight distribution set the acceleration, and more power changes nothing.
Peak power is one point
The quoted figure is the maximum, reached at one engine speed. Through each gear the engine sweeps a range of speeds, so its average power is less than its peak.
Gear changes
While a gear change is in progress, the wheels get reduced power, or none.
Driveline losses
Some power is lost between the engine and the tires. This site’s model assumes about 9% for a two-wheel-drive gasoline car with a manual gearbox and about 5% for a single-speed electric car, each with a stated range.
Drag and rolling resistance
Aerodynamic drag grows with the square of speed, and rolling resistance is treated as constant in this model. Both are subtracted from thrust before anything is left to accelerate the car.
Rotating parts
Wheels, driveline and engine have to be spun up as well as moved forward. That acts like extra mass, most of all in the low gears.
What was counted as mass
A ratio worked out from the car without a driver leaves out the driver, who is on board in any real run. Published masses also differ in what they count, such as how much fuel.

The grip limit can be put in the same terms. If all of the car’s weight were on driven wheels with a grip coefficient μ, the tires could pass a force of μ × m × g, and the power limit P ÷ v would drop below that at v = (P ÷ m) ÷ (μ × g).

At 100 W/kg and μ = 1 that speed is 10.2 m/s (37 km/h). At 300 W/kg it is 30.6 m/s (110 km/h), beyond the end of a 0–100 km/h run: in this idealized case, such a car would be limited by grip, not power, all the way to 100 km/h, and its ratio would say little about that time.

The same ratio, a different result

Scale a car’s power and mass by the same factor and the ratio does not change, but the result does. Aerodynamic drag depends on the car’s shape and size, not its mass. If the drag area stays the same, the larger power pushes against the same air, so drag takes a smaller share of the thrust and the heavier, more powerful car gains at higher speeds.

In this site’s model the rotational inertia assumed for the engine and wheels also stays the same, so it too counts for less in the scaled-up car. The grip limit at low speed does not move, because the force the tires can pass and the mass to be accelerated grow together.

Layout matters as well. Which wheels are driven decides how much of the weight presses on the tires that do the pushing, so two cars with the same ratio can leave the line at different rates.

Try it: change mass, power, or both

The cars are illustrative: made-up vehicles with round numbers, not real ones. Pick what to change and by how much. The model then estimates both times, and the ideal bound for the new ratio is shown beside them.

Inputs

Change
%

Applied to the starting point’s mass, its power, or both by the same factor. Peak torque is scaled with power.

Modeled estimate

Illustrative vehicle

Every result in this section is a modeled estimate for a made-up car. None of it is a figure for a real, named vehicle.

Power-to-weight ratio

84.6W/kg

110 kW ÷ 1,300 kg

113.5 hp per metric ton · 115.0 PS/t

0–60 mph

8.44s

ideal bound 4.25 s

8.25–9.14 s across the assumption ranges

0–100 km/h

8.91s

ideal bound 4.56 s

8.72–9.62 s across the assumption ranges

With 110 kW and 1,300 kg, the illustrative gasoline hatchback has 84.6 W/kg. The model estimates 0–100 km/h in 8.91 s; the ideal bound for that ratio is 4.56 s.

Ratio against time

  • Modeled, power varied (solid line, round marker)
  • Ideal bound (dashed line, square marker)
  • Round marker: the car with your inputs. It leaves the solid line when mass changes.
Modeled 0–100 km/h time against power-to-weight ratio, illustrative gasoline hatchbackModeled 0–100 km/h time against power-to-weight ratio for the illustrative gasoline hatchback with only its power varied, and the ideal bound. With your inputs, at 84.6 W/kg, the model gives 8.91 s and the ideal bound is 4.56 s.
SummaryModeled 0–100 km/h time against power-to-weight ratio for the illustrative gasoline hatchback with only its power varied, and the ideal bound. With your inputs, at 84.6 W/kg, the model gives 8.91 s and the ideal bound is 4.56 s.
Show the data as a table
Modeled 0–100 km/h time and ideal bound by power-to-weight ratio (power varied, mass fixed)
W/kgPower (% of starting point)Modeled (s)Ideal bound (s)
50.860%14.297.60
59.270%12.156.51
67.780%10.645.70
76.290%9.675.07
84.6100%8.914.56
93.1110%8.344.14
101.5120%7.913.80
110.0130%7.573.51
118.5140%7.283.26
126.9150%7.043.04
135.4160%6.892.85

Modeled estimate

Starting point and your inputs

Starting point and your inputs: ratio, ideal bound and modeled estimate
CarMassPowerW/kgIdeal 0–60 mphModeled 0–60 mphIdeal 0–100 km/hModeled 0–100 km/h
Starting point1,300 kg110 kW84.64.25 s8.44 s4.56 s8.91 s

Something to try

With the gasoline hatchback, choose “Both together” and set the change to +50%. The ratio stays at 84.6 W/kg, yet the modeled 0–100 km/h time falls from about 8.9 s to about 8.5 s. Then pick the gasoline coupe, choose “Mass only” and set −20%. The ratio rises by a quarter and the time moves by about three hundredths of a second, because for most of that run the rear tires, not the engine, are the limit.

Assumption

Assumptions used in this run

These inputs are not part of the car’s stated specifications, so the model chooses them. The run above uses the “value used” column; the range line under each time shows how far the result moves when every assumption is varied across its range.

Assumptions used in this run
AssumptionValue usedRange considered
Idle speed (rpm)800700 – 900
Torque at idle ÷ peak torque0.750.60 – 0.88
Power lost between peak-power speed and the rev limit0.080.02 – 0.20
Engine speed held at launch (rpm)4,0002,800 – 5,200
Gear-change time (s)0.350.25 – 0.50
Engine rotational inertia (kg·m²)0.200.10 – 0.35
Drag coefficient (Cd)0.300.26 – 0.36
Frontal area ÷ (width × height)0.840.78 – 0.88
Rolling-resistance coefficient0.0110.008 – 0.014
Loaded tire radius ÷ nominal radius0.9650.950 – 0.980
Driveline efficiency0.910.88 – 0.94
Share of weight on the front axle0.610.57 – 0.64
Center-of-gravity height (m)0.570.52 – 0.61
Rotational inertia per axle (kg·m²)2.21.5 – 3.5
Grip multiplier (tire and surface variation)1.000.92 – 1.08

Conditions

  • Level road, no wind
  • Air density 1.2 kg/m³
  • No occupants or cargo added to the vehicle mass
  • Closed-course, straight-line run from a standstill
  • Ratio uses peak engine power and the mass of the empty car
  • Tire–road grip μ = 1.00
  • Model version 0.3.0

The range is how far the result moves when the assumptions move. It is not a statistical confidence interval against measured results.

How the model works and what it assumes: methodology

What this experiment leaves out

Scaling power here scales the whole torque curve and leaves gearing, tires and drag area alone. A real car with twice the power would not keep the same tires or gearbox, so read the experiment as a statement about the physics, not about any pair of real cars.

The grip coefficient is one constant number in this model. Tire temperature, wear and load sensitivity are not in it.

Modeled estimate
The model has been checked against closed-form physics cases, but it has not yet been compared with instrumented test results for real cars. Until that comparison is published, treat every number here as an illustration of cause and effect, not as a prediction for any particular vehicle.

How the model works and what it assumes: methodology