Guide · Measurement

0–60 mph vs 0–100 km/h: why the two times differ

60 mph is exactly 96.56064 km/h, so a 0–60 mph run and a 0–100 km/h run stop the clock at different speeds. The 0–100 km/h run has to gain a further 3.44 km/h (2.14 mph). The two times are therefore not interchangeable, and no fixed factor converts one into the other.

The extra time is that last 3.44 km/h divided by how hard the car is still accelerating when it gets there. A car pulling 6 m/s² near 100 km/h needs about 0.16 s more; one pulling 3 m/s² needs about 0.32 s; one pulling 1.5 m/s² needs about 0.64 s. If a gear change happens to fall between the two speeds, the gap grows by roughly the length of that shift. Timing conventions such as 1-foot rollout then move both figures again.

Updated Model version 0.3.0

DraftThis page has not completed editorial review. It is hidden from search engines until it has.

Two finish lines, 3.44 km/h apart

A mile is defined as exactly 1609.344 meters, so 60 mph is exactly 96.56064 km/h and 100 km/h is about 62.137 mph. Neither test is a rounded version of the other: they end at different speeds.

Because the difference is a fixed speed rather than a fixed time, how long it takes depends entirely on the car. If acceleration is roughly steady across those 3.44 km/h, the extra time is simply the speed difference divided by the acceleration.

extra time ≈ 0.955 m/s ÷ acceleration

Where each test ends
Testkm/hmphm/s
0–60 mph96.560646026.8224
0–100 km/h10062.13727.778
Difference3.439362.1370.955

km/h3.44 km/h apart

The last stretch of the speed scale, to scale. A 0–60 mph run ends at the first mark; a 0–100 km/h run carries on to the second.
Extra time needed for the last 3.44 km/h (0.955 m/s) at a steady acceleration
Acceleration near 100 km/hExtra time
9.0 m/s²0.11 s
6.0 m/s²0.16 s
4.0 m/s²0.24 s
3.0 m/s²0.32 s
2.0 m/s²0.48 s
1.5 m/s²0.64 s
1.0 m/s²0.96 s

This table is arithmetic (speed difference ÷ acceleration), not a set of measurements.

Try it on an illustrative car

The car below is hypothetical. Its numbers are round values chosen for teaching, not the specification of any real vehicle. Change them and the model recalculates both times, the gap between them, and where the gear changes fall.

Inputs

kg
kW

Peak torque is scaled by the same proportion.

:1

A higher number means shorter gearing: more thrust in each gear, lower top speed in each gear.

Driven wheels
μ

1.0 is this model’s default value.

Modeled estimate

Illustrative vehicle

Every result in this section is a modeled estimate for a made-up car. None of it is a figure for a real, named vehicle.

0–60 mph

8.44s

from rest · in gear 3

8.25–9.14 s across the assumption ranges

0–100 km/h

8.91s

from rest · in gear 3

8.72–9.62 s across the assumption ranges

Gap between them

0.47s

the last 3.44 km/h, at an average of 2.03 m/s²

With these inputs the illustrative gasoline hatchback reaches 60 mph in 8.44 s and 100 km/h in 8.91 s, both counted from rest: a gap of 0.47 s. No gear change falls between the two speeds.

The run, plotted

  • Your inputs (solid line, round marker)
  • Change an input to compare against the starting point.
Speed against time, illustrative gasoline hatchbackSpeed against time. With your inputs the car passes 60 mph at 8.44 s and 100 km/h at 8.91 s.
SummarySpeed against time. With your inputs the car passes 60 mph at 8.44 s and 100 km/h at 8.91 s.
Show the data as a table
Speed, distance, acceleration and gear over time
Time (s)Speed (km/h)Distance (m)Accel. (m/s²)Gear
0.00.00.04.751
0.58.60.64.751
1.017.12.44.751
1.525.65.34.741
2.034.19.54.621
2.542.314.84.441
3.050.021.23.951
3.553.128.5-0.172
4.057.536.13.052
4.563.044.53.032
5.068.453.62.982
5.573.763.52.902
6.078.874.12.792
6.583.785.42.652
7.088.397.32.482
7.592.5109.92.192
8.093.3122.82.063
8.597.0136.02.033
9.0100.6149.72.003
9.5104.2164.01.963
10.0107.7178.71.923

Modeled estimate

The same run, timed two ways

The same run, timed two ways
Clock starts0–60 mph0–100 km/hGap
At first movement (from rest)8.44 s8.91 s0.47 s
After 1-foot rollout8.08 s8.55 s0.47 s
Mixed: 0–60 mph after rollout vs 0–100 km/h from rest8.08 s8.91 s0.83 s

In this run the first foot (0.3048 m) took 0.36 s. Subtracting it shortens both times equally, so the gap is unchanged, unless one figure uses rollout and the other does not.

Gear changes before 100 km/h

  • Gear 1 to 2 at 3.26 s (53.3 km/h)
  • Gear 2 to 3 at 7.60 s (93.2 km/h)
Gear at 60 mph
3
Gear at 100 km/h
3

Something to try

With the gasoline hatchback, lower the final drive ratio from 4.00 to 3.85. Second gear then runs out between the two speeds: 60 mph is reached before the gear change and 100 km/h after it, and the gap roughly doubles.

Assumption

Assumptions used in this run

These inputs are not part of the car’s stated specifications, so the model chooses them. The run above uses the “value used” column; the range line under each time shows how far the result moves when every assumption is varied across its range.

Assumptions used in this run
AssumptionValue usedRange considered
Idle speed (rpm)800700 – 900
Torque at idle ÷ peak torque0.750.60 – 0.88
Power lost between peak-power speed and the rev limit0.080.02 – 0.20
Engine speed held at launch (rpm)4,0002,800 – 5,200
Gear-change time (s)0.350.25 – 0.50
Engine rotational inertia (kg·m²)0.200.10 – 0.35
Drag coefficient (Cd)0.300.26 – 0.36
Frontal area ÷ (width × height)0.840.78 – 0.88
Rolling-resistance coefficient0.0110.008 – 0.014
Loaded tire radius ÷ nominal radius0.9650.950 – 0.980
Driveline efficiency0.910.88 – 0.94
Share of weight on the front axle0.610.57 – 0.64
Center-of-gravity height (m)0.570.52 – 0.61
Rotational inertia per axle (kg·m²)2.21.5 – 3.5
Grip multiplier (tire and surface variation)1.000.92 – 1.08

Conditions

  • Level road, no wind
  • Air density 1.2 kg/m³
  • No occupants or cargo added to the vehicle mass
  • Closed-course, straight-line run from a standstill
  • Tire–road grip μ = 1.00
  • Model version 0.3.0

The range is how far the result moves when the assumptions move. It is not a statistical confidence interval against measured results.

How the model works and what it assumes: methodology

Why a gear change can double the gap

An engine with a gearbox cannot deliver drive continuously. Each gear runs out at some road speed, and during the change the car briefly stops accelerating, or even slows a little. In the model, a manual change takes a few tenths of a second.

If a gear tops out below 96.56 km/h, the change happens before both finish lines and costs both times equally. If it tops out above 100 km/h, it affects neither. But if it tops out between the two, the 0–60 mph time escapes the gear change and the 0–100 km/h time pays for all of it. Two cars with identical power and mass can then show very different gaps, purely because of gearing.

A single-speed electric car has no gear change at all, so its gap is set only by how hard it is still accelerating near 100 km/h.

1-foot rollout: when the clock starts

Under a 1-foot rollout convention, timing begins only once the car has already moved 1 ft (0.3048 m). The car is rolling when the clock starts, so the reported time is shorter than a time counted from the first movement.

For a steady launch acceleration, covering the first foot takes √(2 × 0.3048 m ÷ acceleration). That is a few tenths of a second, which is large next to the differences people argue about.

Rollout shortens 0–60 mph and 0–100 km/h by the same amount, so it does not change the gap between them when both are timed the same way. It matters when you set a figure that excludes the first foot beside one that does not: the apparent difference is then the speed gap plus the rollout time.

Time to cover the first foot at a steady launch acceleration
Launch accelerationTime for the first 1 ft
3.0 m/s²0.45 s
4.0 m/s²0.39 s
6.0 m/s²0.32 s
8.0 m/s²0.28 s
10.0 m/s²0.25 s

Arithmetic for a constant acceleration, not a set of measurements. Real launches are not perfectly steady.

What else differs between published figures

Two published times for the same model can disagree without either being wrong, because a time is only meaningful together with how it was obtained. Before comparing two figures, check whether they agree on these points.

The finish speed
60 mph or 100 km/h. Different tests, as shown above.
When the clock starts
At the first movement, or after a rollout distance.
Who produced the figure
A manufacturer’s claim and an independent instrumented test are different kinds of number, even when they happen to match.
The exact vehicle
Model year, market, trim, transmission, driven wheels, tires and options. A figure for one configuration says little about another.
Mass on board
Driver, fuel load and equipment change the mass being accelerated.
Surface and weather
Grip, air temperature, air pressure and wind all change the result. Check whether the figure was corrected to standard conditions.
How runs are combined
A single best run, an average of several, or an average of runs in opposite directions.
Launch technique
Engine speed at launch, launch-control use and how gear changes are made.

This page does not attribute any of these practices to a particular publication or manufacturer. Where this site later quotes a published figure, the figure will carry its source and the conditions that source states.

How to compare a 0–60 mph time with a 0–100 km/h time

  1. Do not convert one into the other. There is no factor that is right for more than one car.
  2. Check that both figures come from the same kind of source and the same vehicle configuration.
  3. Check whether each includes or excludes rollout. If you cannot tell, treat the comparison as unknown by a few tenths of a second.
  4. Expect the 0–100 km/h time to be the longer one: by roughly 0.1 to 0.65 s for a car still accelerating at between 9 and 1.5 m/s² near 100 km/h, and by more if a gear change falls between the two speeds.
  5. If the remaining difference between two cars is smaller than that uncertainty, the honest reading is that the figures do not separate them.

What this model does and does not include

The experiment uses the same straight-line model as the rest of this site. It is a simplification, and its limits matter most at launch.

Included

  • Engine or motor output through each gear and the final drive
  • Tire grip limit, with weight transfer under acceleration
  • Aerodynamic and rolling resistance
  • Rotational inertia of the engine or motor and the wheels
  • Time lost in each gear change

Not included

  • Turbocharger lag and other transient engine behavior
  • Torque-converter multiplication, launch control and traction-control logic
  • Tire temperature, wear and slip-ratio behavior
  • Battery temperature, state of charge and power limits
  • Driver skill and run-to-run variation
Modeled estimate
The model has been checked against closed-form physics cases, but it has not yet been compared with instrumented test results for real cars. Until that comparison is published, treat every number here as an illustration of cause and effect, not as a prediction for any particular vehicle.

How the model works and what it assumes: methodology