Methodology

Methodology: how the estimates are calculated

Every modeled estimate on this site comes from one physics model of a car accelerating in a straight line. The model moves the car forward in small time steps. At each step the force at the tires is limited by what the powertrain can deliver and by what the tires can pass to the road. Drag, rolling resistance and any gradient are subtracted, and what is left accelerates the car and its rotating parts.

How far can you trust it? The model reproduces textbook cases that have exact answers, but it has not yet been compared with instrumented tests of real cars. Its estimates for real, named vehicles have only been set beside the manufacturers’ own acceleration figures, which is a weaker check. Every estimate is labeled as modeled and shown with a range, and the numbers should be read as cause and effect, not as predictions.

Updated Model version 0.3.0

DraftThis page has not completed editorial review. It is hidden from search engines until it has.

What the model covers

One thing only: a car accelerating in a straight line from a standstill on a closed course. It is one-dimensional, so it knows about forward motion and nothing about cornering, braking or lap times.

It handles cars with an engine and a stepped gearbox (manual, torque-converter automatic or dual-clutch) and battery-electric cars with a single fixed ratio. Hybrids and continuously variable transmissions are outside it.

Four kinds of number

Each figure about a vehicle on this site is one of four kinds, and the kind is shown with it. The model only ever produces the third kind, and it needs the fourth kind to do so. Unit conversions and the calculators in the guides are plain arithmetic and are marked as such.

Manufacturer-claimed
A figure published by the vehicle’s maker, under the maker’s own test conditions. Specifications such as mass, power and gear ratios are of this kind.
Instrumented test (measured)
A figure recorded with timing equipment in a real test of a real vehicle. The model does not produce these. They are what it will be compared against.
Modeled estimate
A figure calculated by the model described on this page from stated inputs. It is not a measurement and not a maker’s figure.
Assumption
An input the model needs but that is not published for the vehicle, such as driveline efficiency or the height of the center of gravity. Each has a most likely value and a range.

The equations

Quantities are in SI units throughout: meters, seconds, kilograms, newtons and watts. Engine speed is in revolutions per minute. The symbols are listed after the equations.

The equation of motion

The body of the car obeys Newton’s second law along the road. On the right-hand side are the driving force the tires actually put into the road and, subtracted from it, everything resisting the car: road load plus, on a slope, the component of weight along the road. The mass is the vehicle mass plus anything added to it, and the acceleration due to gravity is 9.80665 m/s².

A slope is entered as a percentage, the rise per 100 units of horizontal distance, and converted to the angle θ. The experiments on this site use a level road, so θ is zero there.

mbody · a = Ftire − RR = Froad + m · g · sin θθ = arctan(p ÷ 100)

Resistance: rolling, drag and wind

Road load can be described in two ways. The first builds it from a rolling-resistance coefficient and a drag area: rolling resistance is proportional to the weight pressing on the road and does not change with speed, and aerodynamic drag grows with the square of the speed of the air over the car. The illustrative cars and custom vehicles use this form, and so do real cars for which no coast-down coefficients have been published.

The second takes three coefficients from a coast-down test of the actual car, giving road load as a constant, a term proportional to speed and a term proportional to speed squared. When conditions differ from the test, the model scales the constant with mass and the squared term with air density. That scaling is an approximation, because fitted coefficients do not separate cleanly into rolling and aerodynamic parts.

Wind is a constant headwind or tailwind added to the car’s speed to give the air speed. A headwind is positive.

Froad = Crr · m · g · cos θ + ½ · ρ · CdA · vrel · |vrel|Froad = a0 · (m ÷ mref) · cos θ + b0 · v + c0 · (ρ ÷ ρref) · vrel · |vrel|vrel = v + vwind

What the powertrain can deliver

For an engine car, the engine speed follows from road speed, tire radius and the overall gearing in the current gear. The engine torque at that speed, multiplied by the gearing and the driveline efficiency and divided by the tire radius, is the force available at the tires.

An electric car is treated as the smaller of two limits: a constant maximum torque, available from a standstill, and a constant maximum power. The first sets the force at low speed and the second takes over as speed rises. Acceleration stops at the motor’s maximum speed or at the stated top speed, whichever comes first.

The tire radius comes from the size written on the tire: half the rim diameter plus the sidewall height, which is the section width times the aspect ratio. That unloaded radius is then multiplied by a factor slightly below one, because a tire carrying weight rolls on a smaller radius.

n = (v ÷ r) · ig · if · 60 ÷ 2πFpt = T(n) · ig · if · η ÷ rFpt = min(Tmax · i · η ÷ r, Pmax · η ÷ v)r = (drim ÷ 2 + w · s) · kr

The engine torque curve

The specifications this site works from give an engine’s peak torque and peak power with the speeds at which they occur, not the full curve. The model therefore builds a curve by a fixed method that passes exactly through the published points and never contradicts power = torque × rotational speed.

From idle up to the peak-torque speed, torque rises along a curve that starts at a fraction q of peak torque and flattens out as it reaches the peak. If peak torque is quoted over a range of speeds, torque stays at its peak across that range. From there to the peak-power speed, a smooth curve brings torque down to exactly the value that gives the published peak power, arriving so that power is at its maximum there. If peak power is quoted over a range of speeds, power stays at its peak across that range. Above the peak-power speed, power falls away toward the rev limit, losing a fraction d of its peak by the time it gets there.

Many published specifications leave out the rev limit. When they do, the model assumes one: the peak-power speed, or the top of its range, multiplied by a ratio that is itself an assumption with a range.

The two shape values, q and d, are not part of those specifications, so they are assumptions. Varying them is how the uncertainty in the shape of the curve reaches the result.

T(n) = Tmax · (q + (1 − q) · s · (2 − s)), s = (n − nidle) ÷ (nT − nidle)T(n) = TmaxT(nP) = Pmax ÷ ωP, dP ÷ dn = 0 (n = nP)P(n) = Pmax · (1 − d · u²), u = (n − nP) ÷ (nlim − nP)T(n) ≤ Pmax ÷ ω

Rotating parts

Wheels, driveline and engine have to be spun up as the car gains speed. The model accounts for this by treating each rotating part as extra mass. The undriven wheels are carried along by the body, so their share is added to the body’s mass. The driven wheels and the engine or motor sit on the powertrain side, because while the tires are slipping they spin without accelerating the car.

The engine’s share grows with the square of the overall gearing, which is why it matters most in the low gears. It is left out while the clutch is slipping at launch and during a gear change, because the engine is then not rigidly connected to the wheels.

The acceleration is first worked out as if all of the powertrain’s force could be used. The force the tires must then pass to the road is the resistance plus whatever accelerates the body.

mbody = m + Nfree · Jaxle ÷ r²mwheel = Ndriven · Jaxle ÷ r²mrot = Je · (ig · if)² ÷ r²a = (Fpt − R) ÷ (mbody + mwheel + mrot)Ftire = R + mbody · aFtire > Fgrip ⇒ Ftire = Fgrip, a = (Fgrip − R) ÷ mbody

What the tires can pass: grip and weight transfer

The driven tires can pass a force of at most the grip coefficient μ times the load pressing them onto the road. If the force worked out above is larger than that, the tires are at their limit: the force is cut to the limit and the acceleration is recalculated from it.

The load on the driven tires is not fixed. Accelerating shifts weight toward the rear axle, by an amount that grows with the height of the center of gravity h and shrinks with the wheelbase L. That adds to the grip of a rear-driven car and takes from that of a front-driven car. Because the weight shift depends on the acceleration and the acceleration depends on the grip, the two are solved together, which gives the expressions below. An all-wheel-drive car can use the grip of all four tires, reduced by a utilization factor u because a real system does not share the force out perfectly.

μ is a single number for the tire and the surface. It does not change with speed, load or temperature in this model. A grip multiplier, one of the assumptions, scales it up and down to represent variation between tires and surfaces.

For a car taken from published specifications, a second factor stands for the kind of tire it is sold on. A summer performance tire grips a dry road better than an all-season tire, and that can decide the launch of a powerful two-wheel-drive car. Where the specifications name the kind of tire, the factor is set for that kind. Where they do not, it covers both, which makes the range wide.

k = (m ÷ mbody) · h ÷ LWf = m · g · (f · cos θ − (h ÷ L) · sin θ)Wr = m · g · ((1 − f) · cos θ + (h ÷ L) · sin θ)Fgrip = μ · (Wr − k · R) ÷ (1 − μ · k)Fgrip = μ · (Wf + k · R) ÷ (1 + μ · k)Fgrip = μ · m · g · cos θ · u

Launch and gear changes

An engine car launches in first gear with the clutch or torque converter slipping, holding the engine at a fixed launch speed and passing that speed’s torque to the wheels. Once road speed has risen to match, the engine is connected directly.

The model changes up when the next gear would give more force at the tires than the current one, or when the engine reaches its rev limit. A change takes a fixed time. During it a manual gearbox passes no drive at all, and automatic and dual-clutch gearboxes pass a reduced share of it. A single-speed electric car has no gear changes.

Stepping through time, and rollout

The motion is calculated in fixed steps of 0.002 s using the midpoint method: the acceleration is evaluated at the speed the car will have halfway through the step, then applied across the whole step. The moment at which the car passes a target speed or distance almost never falls exactly on a step boundary, so it is solved for inside the step. The result therefore does not depend on how coarse the steps are, to within a few thousandths of a second.

Every time is produced twice: counted from the first movement, and counted from the moment the car has rolled one foot (0.3048 m). The second convention gives a shorter time for the same run. Results on this site are counted from the first movement unless they say otherwise.

From one run the model reports the times to 60 mph and to 100 km/h, and the times and speeds at 100 m, 200 m, 400 m, the quarter mile and 1000 m. The same inputs always give the same result.

vmid = v + a(v) · Δt ÷ 2, a = a(vmid)v ← v + a · Δt, x ← x + v · Δt + ½ · a · Δt²τ = (vtarget − v) ÷ atro = t − t1ft

Frontal area

Drag needs the frontal area of the car. If that has not been given and the overall width and height have, the model takes their product times a factor below one, since a car does not fill the rectangle around it. That factor is an assumption with a range.

A = wv · hv · kA

Symbols

Symbols used in the equations on this page
SymbolMeaning
aAcceleration of the car along the road
mVehicle mass plus any added mass
mbodyMass of the body plus the equivalent mass of the undriven wheels
FtireDriving force the tires put into the road
FptForce the powertrain could deliver at the tires, after driveline losses
FgripLargest driving force the driven tires can pass to the road
RTotal resistance: road load plus the slope component of weight
FroadRoad load: rolling resistance plus aerodynamic drag
gAcceleration due to gravity
θAngle of the road above horizontal
pSlope in percent: rise per 100 units of horizontal distance
vRoad speed
vrelSpeed of the air over the car
vwindHeadwind speed; negative for a tailwind
ρAir density
CdADrag area: drag coefficient times frontal area
CrrRolling-resistance coefficient
a0, b0, c0Coast-down coefficients of the car
mref, ρrefMass and air density that the coast-down coefficients refer to
nEngine speed in revolutions per minute
T(n)Engine torque at engine speed n, from the torque curve
Tmax, PmaxPublished peak torque and peak power
ω, ωPRotational speed in radians per second, and its value at the peak-power speed
ig, if, iRatio of the current gear, final drive ratio, and the total reduction ratio of an electric car
ηDriveline efficiency
rRolling radius of the driven tires
drim, w, s, krRim diameter, section width, aspect ratio, and the factor from unloaded to loaded radius
Jaxle, JeRotational inertia of one axle’s wheels, and of the engine or motor
Nfree, NdrivenNumber of undriven and of driven axles; they add up to two
mwheel, mrotEquivalent mass of the driven wheels, and of the engine or motor while it is connected to them
μGrip coefficient between tire and road, including the grip multiplier
Wf, WrLoad on the front and on the rear axle with the car at rest
fShare of the car’s weight on the front axle at rest on level ground
hHeight of the center of gravity
LWheelbase
kWeight-transfer factor: how strongly acceleration moves load between the axles
uShare of the total grip an all-wheel-drive system can use
qTorque at idle as a fraction of peak torque
dFraction of peak power lost between the peak-power speed and the rev limit
nidle, nT, nP, nlimEngine speed at idle, at peak torque, at peak power, and at the rev limit
ΔtLength of one time step
τ, vtargetTime from the start of a step to the moment the target speed is passed, and that target speed
tro, t1ftTime counted from one foot of travel, and the time at which that foot is covered
A, wv, hv, kAFrontal area, overall width, overall height, and the factor between the rectangle and the true area

Assumptions: most likely values and ranges

The table lists every assumption the model can make. It is generated from the model’s own data when this page is built, so it always shows the values the current model version uses. An assumption is only made when the corresponding value has not been given: a car with a published drag coefficient, for example, does not get an assumed one.

Each assumption has a lowest, a most likely and a highest value. A single run uses the most likely value. Ranges are produced by drawing every assumption from a triangular distribution between its lowest and highest value, peaking at the most likely one.

These values are provisional. They are engineering starting points, not values fitted to tests. They will be reviewed when the model is compared with instrumented tests, and any change will come with a new model version.

Every assumption in model version 0.3.0, with its most likely value and range
What is assumedApplies toMost likelyRangeVariedMainly affects
Grip multiplier (tire and surface variation)Every car1.000.92 – 1.08Together for both carsLaunch, for as long as the tires are the limit
Tire grip relative to an all-season tirePublished specifications, summer tires1.151.05 – 1.30Separately for each carLaunch, for as long as the tires are the limit
Tire grip relative to an all-season tirePublished specifications, all-season tires1.000.92 – 1.08Separately for each carLaunch, for as long as the tires are the limit
Tire grip relative to an all-season tirePublished specifications, kind of tire not stated1.050.92 – 1.30Separately for each carLaunch, for as long as the tires are the limit
Driveline efficiencyEngine, manual gearbox, two driven wheels0.910.88 – 0.94Together for both carsThe whole run
Driveline efficiencyEngine, dual-clutch gearbox, two driven wheels0.900.87 – 0.93Together for both carsThe whole run
Driveline efficiencyEngine, torque-converter automatic, two driven wheels0.890.85 – 0.92Together for both carsThe whole run
Driveline efficiencyEngine, manual gearbox, all-wheel drive0.890.86 – 0.92Together for both carsThe whole run
Driveline efficiencyEngine, dual-clutch gearbox, all-wheel drive0.880.85 – 0.91Together for both carsThe whole run
Driveline efficiencyEngine, torque-converter automatic, all-wheel drive0.870.83 – 0.90Together for both carsThe whole run
Driveline efficiencyElectric0.950.92 – 0.97Together for both carsThe whole run
Loaded tire radius ÷ nominal radiusEvery car0.9650.950 – 0.980Together for both carsThe whole run, through gearing
Rotational inertia per axle (kg·m²)Every car2.21.5 – 3.5Together for both carsThe whole run, slightly
Share of total grip an all-wheel-drive system can useAll-wheel drive0.960.90 – 1.00Together for both carsLaunch of all-wheel-drive cars
Center-of-gravity height (m)Overall height given: the value is a fraction of that height0.390.36 – 0.42Separately for each carLaunch of two-wheel-drive cars
Center-of-gravity height (m)Overall height not given: the value is in meters0.520.45 – 0.60Separately for each carLaunch of two-wheel-drive cars
Share of weight on the front axleFront-wheel drive, weight distribution not given0.610.57 – 0.64Separately for each carLaunch of two-wheel-drive cars
Share of weight on the front axleRear-wheel drive, weight distribution not given0.520.47 – 0.56Separately for each carLaunch of two-wheel-drive cars
Share of weight on the front axleAll-wheel drive, weight distribution not given0.570.52 – 0.61Separately for each carLaunch of two-wheel-drive cars
Idle speed (rpm)Engine cars800700 – 900Together for both carsThe lowest engine speeds
Torque at idle ÷ peak torqueEngine cars0.750.60 – 0.88Together for both carsLow engine speeds, below peak torque
Power lost between peak-power speed and the rev limitEngine cars0.080.02 – 0.20Together for both carsThe top of each gear and the choice of change-up point
Rev limit ÷ peak-power speedEngine cars, rev limit not given1.121.04 – 1.20Separately for each carHow far each gear can be held before changing up
Engine speed held at launch (rpm)Example: the illustrative gasoline hatchback, manual gearbox4,0002,800 – 5,200Together for both carsLaunch of engine cars
Engine speed held at launch (rpm)Example: the same car with a torque-converter automatic2,4001,680 – 3,120Together for both carsLaunch of engine cars
Gear-change time (s)Manual gearbox0.350.25 – 0.50Together for both carsEvery gear change
Gear-change time (s)Dual-clutch gearbox0.100.05 – 0.15Together for both carsEvery gear change
Gear-change time (s)Torque-converter automatic0.250.15 – 0.40Together for both carsEvery gear change
Share of drive kept during a gear changeDual-clutch gearbox0.850.60 – 1.00Together for both carsEvery gear change
Share of drive kept during a gear changeTorque-converter automatic0.800.50 – 1.00Together for both carsEvery gear change
Engine rotational inertia (kg·m²)Engine cars0.200.10 – 0.35Together for both carsThe low gears
Motor rotational inertia (kg·m²)Electric0.050.02 – 0.10Together for both carsThe whole run of an electric car, slightly
Rolling-resistance coefficientRoad load built from rolling resistance and drag area0.0110.008 – 0.014Together for both carsThe whole run, slightly
Frontal area ÷ (width × height)Frontal area not given, width and height given0.840.78 – 0.88Together for both carsHigher speeds
Frontal area (m²)Frontal area, width and height not given2.201.90 – 2.60Separately for each carHigher speeds
Drag coefficient (Cd)Drag coefficient not given0.300.26 – 0.36Separately for each carHigher speeds
  • The launch speed has no single value: it is set from the engine’s own peak-torque speed for manual and dual-clutch gearboxes and at a fixed speed for torque-converter automatics, then kept below the peak-power speed. The two rows show what that gives for one example car.
  • A manual gearbox passes no drive during a gear change. That is fixed in the model, not an assumption, so it has no row.
  • For road load given as coast-down coefficients, the model assumes the coefficients refer to an air density of 1.17 kg/m³. That value has not yet been checked against the test standard, and it only matters when the air density is changed.

How ranges and comparisons are produced

A range on this site answers one question: how far does the result move when the assumptions move? The model is run 120 times, each time with every assumption drawn afresh from its range, and the range shown runs from the 5th to the 95th percentile of those results. It is not a statistical confidence interval against measured results, and this site does not call it one.

Assumptions are of two kinds. Shared assumptions describe the model, the road and the way the car is driven: grip, driveline efficiency, gear-change time, the shape of the torque curve. Per-car assumptions are unknown facts about one particular car: the height of its center of gravity, or its weight distribution or drag coefficient when those are not given.

To compare two cars, the two ranges are not simply laid side by side. Most of each range comes from the shared assumptions, which affect both cars in the same direction, so two ranges would overlap even when one car is ahead in nearly every run. Instead, in each run both cars get the same values for the shared assumptions and their own draws for the per-car ones, and the model records the difference between their times.

One car is called quicker only if it is ahead in at least 90% of those runs. Otherwise the result is “too close to call”, whichever car has the lower single estimate. If either car fails to reach the target in more than one run in ten, no comparison is shown at all.

The 90% threshold is provisional. It will be set once, from the results of comparing the model with instrumented tests, and not changed afterwards to suit a particular comparison.

Runs are repeatable. The same inputs, model version and seed give the same draws and therefore the same range, in your browser and when these pages are built.

Explaining a difference

To show where a difference comes from, the model takes one car, replaces one group of its inputs with the other car’s (mass, engine or motor, gearing, traction layout, or road load) and runs it again with every assumption at its most likely value. The change in time is reported for each group.

These are not percentage contributions. The inputs interact, so the separate effects do not add up to the whole difference. The part left over is reported as it is and is not shared out among the inputs.

What is not in the model

Each of these simplifications can move a real car’s time away from the model’s, and several of them act at launch, where a short run is decided.

  • Launch is simplified to a clutch slipping at a constant engine speed. Torque multiplication in a torque converter, launch control and the response of traction control are not modeled.
  • There is no turbocharger lag. The steady-state torque curve is available at once.
  • The change-up rule compares the force in the current and the next gear at that instant. It does not weigh the time lost in the gear change itself.
  • The tire has one constant grip coefficient. Slip behavior, temperature, wear and aerodynamic load are not modeled, and the tire radius does not change with speed.
  • An electric car’s power is not limited by battery temperature or state of charge.
  • Mass added to the car, such as occupants, does not change the weight distribution.
  • The engine torque curve is reconstructed from a few published points. The real curve of a particular engine can differ, most of all below its peak-torque speed.
  • Wind is constant along the run, and the road has a single constant slope.
  • Adjusting coast-down coefficients for mass and air density is an approximation, and whether such coefficients overlap with the driveline-efficiency assumption has not been settled. No vehicle on this site uses that form of road load yet.
  • Hybrids, continuously variable transmissions, cornering, braking and driving on public roads are outside the model.

What has been checked, and what has not

Checked

These checks run automatically whenever the model changes.

  • Cases with exact answers: a constant force, a constant power, acceleration set by grip for rear-, front- and all-wheel drive, a slope, and the speed at which drive and drag balance.
  • Changing the time step between 0.0005 s and 0.004 s moves the 0–100 km/h and quarter-mile times of a test car by less than 0.005 s.
  • How often points are recorded for plotting does not change the result, and the same inputs give the same result every time.
  • Energy balances: the work done at the tires equals the work against resistance plus the gain in height and kinetic energy.
  • 60 mph and 100 km/h are kept as separate targets, and times with rollout differ from times without it by exactly the time taken to cover the first foot.
  • More mass, an uphill slope, a headwind, a slippery surface and slower gear changes each make the test car slower.
  • Five hundred randomly generated cars produce no undefined values, no runaway speeds, no rolling backwards and no time running backwards.
  • A car that cannot move, or cannot reach a target within the run, is reported as such. No number is made up for it.

Not yet done

  • The model has not been compared with instrumented tests of real cars. The assumption values above have not been tuned against any measurement either.
  • Modeled times for real, named vehicles are therefore shown as estimates with ranges, and each is marked as not compared with tests. As a weaker check, the estimates have been set beside the manufacturers’ own 0–60 mph figures for the configurations that have one; the table below shows the result. The model is not tuned to those figures: they are the makers’ claims, timed under conditions this site has not established.
  • If a comparison with instrumented tests is made, this page will show its results: which tests were used and how large the errors were.

Beside the manufacturers’ figures

Where a manufacturer publishes a 0–60 mph figure for a configuration, the table sets that figure beside the modeled range for the same configuration. This is not a comparison with measurements. The figures are the makers’ own, and their documents do not say how they were timed: the launch method, whether the first foot of travel is left out, the surface and the load are not stated.

The manufacturer’s figure falls inside the modeled range for 8 of 11 configurations. The middle of the modeled range differs from the manufacturer’s figure by 6% at the median and by 10% at most. Wherever the figure falls outside the range, it is slower than the range.

A range that misses the manufacturer’s figure is left as it is. An assumption is changed only when public evidence about that assumption itself turns up, such as a published measurement of the quantity. It is never changed to move an estimate toward a claimed time.

None of the electric cars with an estimate on this site has a manufacturer’s 0–60 mph figure, so their estimates have not been checked even in this weaker way.

0–60 mph: the manufacturer’s figure and the modeled range. The modeled range is timed from first movement with a 75 kg driver, on a flat, dry surface.
ConfigurationManufacturer’s figure (s)Modeled range (s)Where the figure falls
2025 BMW 3 Series 330i, 8-speed automatic (US)5.65.24 – 5.99Inside the range
2025 BMW 3 Series M340i xDrive, 8-speed automatic (US)4.13.86 – 4.29Inside the range
2025 BMW M2, 6-speed manual (US)4.14.08 – 4.72Inside the range
2025 BMW M2, 8-speed automatic (US)3.93.73 – 4.40Inside the range
2025 Porsche 911 Carrera, 8-speed dual-clutch (US)3.93.48 – 3.890.01 s slower than the range
2025 Toyota GR Corolla Core, 6-speed manual (US)4.94.66 – 5.33Inside the range
2025 Toyota GR Corolla Core, 8-speed automatic (US)4.94.28 – 4.830.07 s slower than the range
2025 Toyota GR Supra 3.0, 6-speed manual (US)4.24.14 – 4.74Inside the range
2025 Toyota GR Supra 3.0, 8-speed automatic (US)3.93.88 – 4.49Inside the range
2025 Toyota GR86, 6-speed automatic (US)6.65.62 – 6.360.24 s slower than the range
2025 Toyota GR86, 6-speed manual (US)6.15.93 – 6.81Inside the range

See every configuration and its sources

Model version and corrections

The current model version is 0.3.0. The version number changes whenever something that can alter a result changes: an equation, the most likely value or range of an assumption, or the numerical method. The version is shown beside every modeled result, and a link to a set of inputs records the version it was made with, so a result can be traced to the model that produced it.

A result is fixed by four things: the inputs, the model version, the conditions and the seed used for the draws. Given the same four, the model returns the same result.

If you find a mistake in an equation, in an assumption or in the explanation on this page, please report it.Report an error